Chemical Resistance
Ceramic Cover CC Systems 100 is an 84% solid latex high density material low in viscosity coating with high insulating properties and chemical resistance. Envirotrol has worked with industry by testing chemical resistivity according to requests.
A Sterilization Division uses Ethylene Glycol, Sulfuric Acids and Ethylene Oxide (gaseous) for sterilization of hospital equipment and supplies. Areas designated for applications of Ceramic Cover CC Systems 100 are the metal roof area (repel gases being expelled causing corrosion), pre-conditioning cell duct systems (stop condensate and hold in heat ), and post-cell duct systems (to seal duct system by retarding gas expulsion).
Ceramic Cover CC Systems 100 tested for reaction against the following chemicals:Envirotrol has worked with the industry by testing chemical resistivity according to requests.
An environmental lab in Alpharetta, GA, uses sodium hydroxide for removal of contaminates in water. Sodium hydroxide violently attacks the aluminum mixing paddles accelerating corrosion.
Two tanks at a pulp and paper plant in the midsouth, 1) a hot water tank, approximately 40' dia. x 30' ht. with a measured temperature of 140ºF, 2) a chemical storage tank, approximately 40'dia. x 40' ht. with a measured temperature of 195ºF. Each had the fiberglass insulation removed and pressure washed.
Ceramic Cover CC Systems 100 was then applied, two (2) coats at approximately forty (.40) mils dft. from ground level to approximately ten feet around each circumference, reducing the hot water temperature to ambient, and the chemical storage tank to 107ºF.
After only one hour of completing application of Ceramic Cover CC Systems 100 the product from the chemical process splashed on the hot water tank. During clean-up the chemical was easily washed off the Ceramic Cover CC Systems 100 with no adverse reactions, disbondment or staining.
Ceramic Cover CC System 100
Insulation
Test results have proven that one coat or 20 mil of Ceramic Cover CC Systems 100 eliminates radiant heat and reduces temperature greatly (60ºF to 80ºF degrees) on hot surfaces. Additional coats contribute a reduction in temperature between 40ºF to 45ºF.
Protection from UV Rays
Ceramic Cover CC Systems 100 can be applied directly over composites with 100% adhesion and no chemical adverse effect (i.e. tar roofing, asphalt shingles, paint, etc.) providing protection against UV Rays as well as insulating.
Adhesion
Ceramic Cover CC Systems 100 reaches full adhesive strength prior to final cure. Also based on disbondment within the coating, Ceramic Cover CC Systems 100 shows an actual stronger bond to the substrate surface.
Flame Resistance
Ceramic Cover CC Systems 100 flame spread is rated 5 out of 100 according to Southwest Research Institute, Department of Fire Technology in San Antonio, TX and MSDS sheet reports flash point noncombustible. Therefore, Ceramic Cover CC Systems 100 can be applied directly to hot surfaces in a wide temperature ranging from 34ºF to 400ºF without shut down.
Corrosion Protection
Ceramic Cover CC Systems 100 has no air pockets, therefore it impedes condensation, stops corrosion and has no loss of insulation properties when wet.
Condensation
Ceramic Cover CC Systems 100 has properties that are impervious to the environment such as a fungal-pesticide resistance - rating of 10 on a scale of 1 to 10 (10 being the highest). Additional tests have been administered: wind driven rain, hot/cold cycling, and chemical resistance. In each test and/or analysis, Ceramic Cover CC Systems 100 "tested in the highest percentiles" of available products.
Chemical Resistance
Ceramic Cover CC Systems 100 is an 84% solid latex high density material low in viscosity coating with high insulating properties and chemical resistance.
Chemical Content
Harland Associates Research Lab in San Francisco, CA, reports Ceramic Cover CC Systems 100 as having
0 (zero) grams of volatile organic compounds, (VOC's) less water per liter, and "is a compliant
coating with regard to VOC content requirement of the Bay Area,
Air Quality Management District," one of the strictly controlled air quality management districts in the U.S.A.
Need Adobe Acrobat Reader? 